The Problem

The all-pervasive phenomenon of metal corrosion affects critical infrastructure and vital installations, not to speak of our everyday lives. It leads to

Massive monetary loss estimated at 4% of national GDP,

Structural instability threatening safety,

Indirectly contributes to environmental degradation

Moreover, several studies have indicated mechanical and chemical methods of surface preparation and steel scrappage directly impact carbon footprint. The toxic discharge of corrosion inhibitors and harmful chemical constituents of protective coatings also contribute to environmental disparity.

All these problems have been exacerbated due to rampant industrialization with unrestrained polluting emissions. Proper redressal of this problem requires recognition of the electrochemical nature of metals and their alloys, both ferrous and non-ferrous, in relation to the environment of exposure, in particular, their vulnerabilities to acidic, neutral, and alkaline conditions.

Electrochemical corrosion happens when metal dissolves (anodic reaction) and corrosion products form (cathodic reaction) in the presence of liquids and air. The environment plays a big role, not just the type of metal. Things like the gases and liquids around, like acids or salt, can affect how corrosion happens. Other factors like humidity, wind speed, and the type of ions in the liquid can make corrosion worse, especially the cathodic reactions.

Problems faced by Existing Coating Solutions

Barrier protective coatings with epoxies as their mainstay are normally prevalent. These provide good to excellent chemical resistance but have serious limitations in corrosion protection. As every coating contains somealbeit limited pathways of electrolyte diffusion into the coating-metal interface through its pores, barrier property alone is insufficient to stem corrosion. Corrosion inhibitors incorporated in such coatings are often unevenly deposited on the metal surface leading to corrosion and pitting. Interfacial corrosion through electrolyte penetration prior to actual coating film detachment leads to metal loss and repeated metal surface preparation during maintenance.

This is not only expensive but will also lead to eventual replacement of painted structures. Zinc based paints/coatings are known to be susceptible to acidic and strongly alkaline attack leading to premature failures in such atmospheres. Even colour-coated galvanized and Galvalume sheets have been found wanting in roofing and cladding applications in industrial installations when exposed to acidic fumes. Extensive surface preparation is absolutely vital for present day protective coatings both on new structural steel as well as pre-painted existing structures. Such preparation ideally calls for grit/shot blasting which is environmentally damaging, tedious, and often unsafe at industrial sites. Similarly galvanized structures (HDG) requireelaborate surface preparation prior to paint application and painted structures are rapidly depleted of zinc in aggressive environments.

Approach to a Solution

Concept of metal passivation

As electrolyte penetration can be impeded but not entirely thwarted a viable method of metal passivation is the key to combat electrochemical corrosion. This would fundamentally alter the active metal interface and prolong life to the fullest possible extent. Moreover this will help reduce coating thickness and thus have a beneficial impact on adhesion. As active ‘white metal’ is highly prone to aerial oxidation such passivation should ideally be achieved even on oxidized ferrous and non-ferrous substrates.

Estimating the extent of corrosion

While many methods are prescribed for evaluating the corrosion resistance of painted metal, the most important measure of active metal loss is obtained by electrochemical impedance studies (EIS). A fair index of undercutting is obtained through creepage emanating from the scribe line in salt fog exposure. However, studies should include metal loss and adhesion on pre-rusted steel as being more representative of real-life situations in maintenance applications.

Estimating the extent of corrosion

While many methods are prescribed for evaluating the corrosion resistance of painted metal, the most important measure of active metal loss is obtained by electrochemical impedance studies (EIS). A fair index of undercutting is obtained through creepage emanating from the scribe line in salt fog exposure. However, studies should include metal loss and adhesion on pre-rusted steel as being more representative of real-life situations in maintenance applications.

1. No Sand/Shot/Grit Blasting

Eliminates surface preparation, including sand/shot/grit blasting, even for rusted surface.

2. No Metal Loss

No loss in thickness of the metal as it prevents undercutting and propagation of rust.

3. Quick Dry

Quick dry and rapid cure leads to minimum plant shut down time.

4. Cost Effective

The ultimate protection cost will be much lower over a 5 year life cycle of the metal.

5. ECO-Friendly

Chromate free, halogen free, isocyanate free, non-toxic, environment friendly product

6. Acid/Alkali Resistant

Exemplary performance in intensely corrosive atmosphere, acidic and alkaline, and saline.

7. Long Pot Life

Metguard’s pot life matches the endurance it promises: a container of Metguard can last for more than 12-15 hours without losing its potency and efficacy.

8. Underfilm Corrosion

There will be no underfilm corrosion under the vigilance of Metguard; Metguard’s extra shield offers a sacrificial layer that corrodes instead of the substrate.

Advantage Of Metguard

METGUARD coating scheme is characterized by

Exceptional adhesion to pre-rusted erected...

Exceptional adhesion to pre-rusted erected, as well as mill scale covered new steel, ferrous alloys, galvanized steel, steel coated with zinc-aluminium alloys, aluminium alloys etc. and thus elimination of rigorous grit/shot blasting techniques as a prelude to paint application

Outstanding resistance to dry heat (up to 200°C)...

Outstanding resistance to dry heat (up to 200°C) and thermal cycling

Toughness and high cohesive strength....

Toughness and high cohesive strength (scratch hardness of 3-5Kg – IS 101-pt.5;sec-2) in film thickness between 140 to 220 microns

Unmatched resistance to undercutting on steel...

Unmatched resistance to undercutting on steel and metalized steel and filiform corrosion on aluminium

Chromate, isocyanate, and halogen free...

Chromate, isocyanate, and halogen free eco-friendly technology

Application Areas

I

All industrial infrastructures exposed to hostile emissions located inland or on the coast;

I

Metalized roofing and cladding panels exposed to acid fumes

I

Heavy duty transportation, locomotives and rails;

I

Rebars used in embedded concrete structures;

Application Areas

I

All industrial infrastructures exposed to hostile emissions located inland or on the coast;

I

Metalized roofing and cladding panels exposed to acid fumes

I

Heavy duty transportation, locomotives and rails;

I

Rebars used in embedded concrete structures;